Master MGH3000 Manual de Instalação descarregar pdf (Página 12)

12

106813

PORTABLE GASOLINE GENERATORS

R

Figure 23 - Engine Switch In ON Position (All

Models Except MGH5000DIE, MGH6500IE,

MGH10000A, and MGH3000PR)

ENGINE SW

ON

OFF

OPERATION

Continued

Fuel Valve Lever (ON Position)

Choke Lever (Closed Position)

Figure 19 - Fuel Valve Lever On, Choke Lever

Closed (Model MGH4000C Shown)

Figure 21 - Choke Button Closed (Model

MGH10000A Only)

Choke Button

Pulled Out

(Closed

Position)

Figure 20 - Choke Rod Closed (Model

MGH3000PR Only)

Choke Rod

Pulled Out

(Closed

Position)

Figure 22 - Engine Lever In ON Position

(Model MGH3000PR Only)

Note: If oil level is too low, oil alert system

will keep engine from starting (see Oil Alert

System, page 6). Make sure oil level is full

before starting. See Engine Oil, page 7.

Before starting the engine, disconnect all

electric loads from generator.

STARTING

IMPORTANT: The engine speed is preset.

The throttle is locked in preset position. Do

not adjust throttle. Preset position lets engine

run at 3600 RPM under load. The engine

must maintain 3600 RPM for generator to

create correct voltage. Running engine at

lower speeds will damage generator and

powered items.

IMPORTANT:

Never start generator with

electrical loads connected. Start engine

before adding electrical loads.

1. Make sure gasoline tank is full. See

Fuel, page 7 for fuel information.

2. Move fuel valve lever to the ON posi

-

tion except on Model MGH3000PR

(see Figure 19).

3. Move choke lever fully to the left for

all models except MGH3000PR or

MGH10000A (see Figure 19). Pull

choke rod out for Model MGH3000PR

(see Figure 20) or choke button out for

Model MGH10000A (see Figure 21).

This closes the choke.

Note: You may not need to close choke

if engine is warm or air temperature is

high.

WARNING: Only responsible

adults should use generator.

Never let anyone operate genera-

tor without proper instructions.

PRESTART

Operate generator on a ﬁrm, dry, and clean

surface. The surface must be level. Protect

generator from heavy dust, sand, dirt, rain,

or snow. Do not locate generator near

standing water and snow. Make sure area

is well-vented.

4. Start the engine.

A. Recoil Starter

Move engine lever or turn engine

switch to the ON position (see Figures

22 and 23). Remove slack from starter

rope by lightly pulling starter grip.

Next, pull starter rope briskly.

IMPORTANT: Do not let starter grip

snap back against engine. Return it gen

-

tly. This will prevent damage to starter.

Note: If engine does not start, check

the oil in the crankcase. Add oil as

necessary. Be sure engine is on a level

surface. See Oil Alert System, page 6.

B . E l e c t r i c S t a r t e r ( M o d e l s

MGH5000DIE, MGH6500IE, and

MGH10000A Only)

Turn the engine switch to the START posi-

tion (see Figure 24, page 13). Hold it there

until engine starts. When engine starts, let

switch return to the ON position.

IMPORTANT: Do not use electric

starter more than ﬁve seconds. Starter

motor damage may occur. If engine

fails to start, release the switch and

wait ten seconds. After ten seconds, try

starting again.

Note: If engine does not start, check

the oil in the crankcase. Add oil as

necessary. Be sure engine is on a level

surface. See Oil Alert System, page 6.

5. As engine warms up, slowly move

choke lever fully to the right (see Figure

25, page 13). This opens the choke. On

Model MGH10000A, the choke will

automatically open.

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 35 36

Comentários a estes Manuais

Sem comentários